China is a big auto country, and timely and effective braking is especially important. In rice harvesting equipment technology (taking small rice harvester as an example), because the rice harvesting equipment often has large volume, weight under full load condition, the rice harvest in the process of frequent change of turning to wait for a characteristic, so the requirement for rice harvesting equipment braking performance is very high, many of which brake technology can be reference to the automobile brake system. The purpose of this article is to solve the existing problems of automobile brake system, and strive to create a more efficient braking system, with multiple disk brake in rice harvesting equipment, air pressure brake, hydraulic brake technology as the foundation, the automobile braking system on the improvement design, for every car brake system after improvement the strict investigation and inspection, and expand the study of the experiment. Research results show that the design of the automobile braking system based on the technology of rice harvesting equipment performance is better, and when using this modified car brake system, automobile brake time shortened by 20%, the wastage of the automobile brake pad was reduced by 25%, the body in the process of braking stability increased by 31%, to prove the feasibility of the modified brake system.

Lijun Lin. Rice Harvesting Equipment Technology in Automobile Brake System. Academic Journal of Agricultural Sciences (2020), Vol. 1, Issue 1: 25-38. https://doi.org/10.38007/AJAS.2020.010103.

[1] Ali P. (2017). “Status and Constrain for Mechanization of Rice Harvesting System in Bangladesh”, Agricultural Sciences, 8(6), pp.492-506. https://doi.org/10.4236/as.2017.86037

[2] Premnath S, Devaradjane G. (2015). “Improving the Performance and Emission Characteristics of a Single Cylinder Diesel Engine Having Reentrant Combustion Chamber Using Diesel and Jatropha Methyl Esters”, ecotoxicology & environmental safety, 121(4), pp.10-15. https://doi.org/10.1016/j.ecoenv.2015.07.033

[3] Ma Z, Chen Z, Jia Y. (2017). “Power, Economy and Emission Characteristics of Low Power Non-Road Diesel”, Transactions of the Chinese Society of Agricultural Engineering, 33(21), pp.78-84.

[4] Yi L, Bowen X, Bin G. (2015). “Dynamic Modeling and Experimental Verification of Bus Pneumatic Brake System”, Open Mechanical Engineering Journal, 9(1), pp.52-57.

[5] Demic M, Glisovic J. (2017). “Contribution to Research of Thermal Loads in Commercial Vehicles Powertrain Mounts”, Military Technical Courier, 65(4), pp.882-903. https://doi.org/10.5937/vojtehg65-14028

[6] Kaimal V K. (2015). “An Analysis on Combustion Characteristic of CI Engine Using Cotton Seed Methyl Ester and Its Blends”, International Journal of Renewable Energy Research, 5(2), pp.586-590.

[7] Ravi M, Kumar K C K V, Murugesan A. (2015) “Certain Investigations on the Performance of Emission, Vibration and Noise Characteristics of C.I Engine Using Bio Gas and Bio Diesel as Alternate Fuel”, International Journal of Pharmtech Research, 8(1), pp.11-19.

[8] Siddique M A A, Rahman M M, Amin M R. (2016). “Performance Study of Manual Reaper Compared to Manual Harvesting for Rice and Wheat”, Agricultural Engineering International the Cigr E Journal, 18(4), pp.165-170.

[9] Shang L, Wu D, Pu Y. (2015). ‘Experimental Research on Thermal Insulation Performance of Lightweight Ceramic Material in Oxidation Environment up to 1700°C”, Ceramics International, 42(2), pp.3351-3360. https://doi.org/10.1016/j.ceramint.2015.10.129

[10] Wu Q, Gao W. (2016). “Research on Passive Design Optimization About an Experimental Rural Residence in Hot Summer and Cold Winter Region of China”, Journal of Building Construction & Planning Research, 4(3), pp.131-156. https://doi.org/10.4236/jbcpr.2016.43009

[11] Adel Ghouari. (2016). “Data Monitoring and Performance Analysis of a 1.6kWp Grid Connected PV System in Algeria”, International Journal of Renewable Energy Research, 6(1), pp.34-42.

[12] Meng FC, Liu YH, Chu JL. (2015). “Experimental Investigation and Performance Evaluation of a Three in Ane Vapour Compression System using Refrigerant R134a”, International Journal of Engineering & Technical Research, 4(5), pp.1346-1352. https://doi.org/10.17577/IJERTV4IS051075